| Stepped by 1 increment |
 |
 |
- stepped shaft enables an extremely precise mounting due to fit - stepped as a stop serves as a restriction in an axial direction - secured in both axial directions possible via a shaft holder screwed to the component or through gluing - less used for linear shafts, otherwise it can be used as a floating bearing |
- fixed bearing: press-fit - press fit - floating bearing: floating bearing seal - clearance fit - bonding possible as fixation |
| Stepped by 2 increments |
 |
 |
- stepped shaft enables an extremely precise mounting due to fit - stepped as a stop serves as a restriction in an axial direction - secured in both axial directions possible via a shaft holder screwed to the component or through gluing - less used for linear shafts, otherwise it can be used as a floating bearing |
- fixed bearing: press-fit - press fit - floating bearing: floating bearing seal - clearance fit - bonding possible as fixation |
| Stepped with threaded pin in fitting diameter |
 |
 |
- highly accurate mounting is possible with a threaded pin and fitting hole at the bearing point - stable under heavy loads, horizontally and for long lengths |
Fixed bearing |
| Stepped with threaded hole, front |
 |
 |
- highly accurate mounting is possible thanks to a stepped shaft with fitting and threaded holes - stable under heavy loads, horizontally and for long lengths - the shaft diameter can be freely adjusted according to the drill holes |
Fixed bearing |
| Stepped with ring groove (stationary axle) |
 |
 |
- not suitable as fixed bearing for linear shafts as the circlips are limited in terms of axial load bearing capacity - no anti-twist protection |
Floating bearing |
| Clamping surface, one-sided/D-shape |
 |
 |
- anti-twist protection - length compensation is possible in case of temperature fluctuations |
Floating bearing |
| Internal thread, front, double |
 |
 |
- counterbore/fitting hole allows for highly accurate mounting by fitting with shaft - stop and locking is possible in both axial directions via 2 screw connections with component - anti-twist protection - also suitable for mounting a torsion-proof end disc |
Fixed bearing |
| Internal hexagon, front |
 |
 |
- as an alternative to the key area in critical installation conditions - front internal hexagon for easier shaft mounting - serves as a drive for shafts with threads at the other shaft end, among other things |
- |
| Tapered |
 |
 |
- primarily as a mounting aid (insertion aid) - simplifies mounting of sealing rings or linear bearings without damaging them - unsuitable for the use with frequent installation with linear bushings. (It may damage the linear bushings.) |
- |
| Fitted hole with stepped threaded hole, front |
 |
 |
- a fitting screw as a guide/centering in combination with the fitting hole of the shaft and threaded holes enables extremely precise mounting. - stable under heavy loads, horizontally and for long lengths |
Fixed bearing |
| Ring groove for shaft retaining ring |
 |
 |
- unsuitable as a fixed bearing for linear shafts as the circlip in axial load-bearing capacity - no anti-twist protection - can also be used as a fixed bearing in combination with a shaft holder bolted to the support structure. |
Floating bearing |
| Threaded hole, front and spanner flats |
 |
 |
- exact mounting is possible due to fit - locking in axial directions via front screw connection - key areas for simple mounting in confined spaces - with a conical through hole, the shaft; it can be centered in the cone and pressed - if in doubt, secure by gluing |
Fixed bearing |
| Transverse spring groove (keyway) |
 |
 |
- exact mounting is possible due to fit - locking in axial directions via keyway - anti-twist proof due to the key |
Fixed bearing |
| Wrench flats/clamping surface - flattened on two sides at the end with locking groove and transverse internal thread for lateral tension |
 |
 |
- for tensioning or parallel alignment of shafts |
Floating bearing |
| Tapped hole crosswise for shaft support profiles |
 |
 |
- linear shaft bolted to shaft support profile |
Fixed bearing |
| Straight solid shaft |
 |
 |
- simple shape - mounting in conjunction with shaft holders |
Fixed bearing |
| Solid shaft with external thread in shaft diameter |
 |
 |
- easy installation - inaccuracies possible due to thread tolerances - if in doubt, secure by gluing |
Floating bearing/fixed bearing |
| Solid shaft with internal thread/threaded hole, front |
 |
 |
- easy to mount with screws through due to through holes - low accuracy of the mounting position - horizontal fastening in low load applications |
Fixed bearing |
| Groove for set screw |
 |
 |
- grub screw clamping/clamping screw clamping - without risking shaft surface damage |
Fixed bearing |
| Stepped by 2 increments and threaded pin |
 |
 |
- highly accurate mounting is possible due to a stepped shaft with a fit and threaded pin - the stepping enables limiting the axial direction - shaft diameter can be freely varied when multiple shafts are used in a base plate with the same bore diameter - if in doubt, secure by gluing |
Fixed bearing |
| Front threaded hole and cross hole |
 |
 |
- secured against axial tension - cross hole as a mounting aid in difficult-to-reach areas - if in doubt, secure by gluing |
Floating bearing |