GANTER Clamping Parts (Screw Accessories)

?* Information on days to ship and prices

• • Promotional pricing ends 30/11/2024

  

  T-Nuts / GN 507 / M4, M5, M6, M8

  GANTER

  T-nuts GN 507 have been specially designed for use on extrusion rails. They are inserted from either end of the T-slot.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	1.06 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  T-Nuts for T-Slots

  GANTER

  T-Nuts GN 505 can be inserted vertically into a T-Slot like rhombus T-Nuts GN 508.1.
  When tightening the clamping bolt, the nut will be forced into a crosswise position by the applied torque and firmly anchored in the T-slot.
  This action is achieved by using T-nut type MB which is intentionally fitted with an overtight fit requiring a higher torque.
  To remove the bolt and T-nut a 90° anticlockwise turn is sufficient to withdraw the two components with the clamped workpiece.
  The clamping face of the T-nut is serrated to ensure that a possible plating coat in the T-slot is penetrated to establish a good electrical contact.
  

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	0.86 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  T-Nuts / Stainless Steel / GN 508 / M6, M8, M10, M12, M14, M16

  GANTER

  Stainless Steel-T-Nuts DIN 508 are also available without tapped hole.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	5.70 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  T-Nuts, Extract

  GANTER

  Beyond the scope of the official standard sheet DIN 508, there is also a choice of additional sizes a = 16, 20 and 24 and a selection of various thread sizes d.
  T-Nuts DIN 508 untapped with the tensile strength class 8 (blank) are also available. When ordering the latter the thread size is omitted in part number.

  • Volume Discount

  Starting from∗ ：	1.36 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  T-Slot bolts for T-Nuts

  GANTER

  T-Slot bolts GN 505.4 can be inserted vertically into the slot. During tightening, the bolt is forced into the crosswise position and thus anchored in the slot. Conversely, the bolt is turned back during loosening and can then be removed.
  The clamping face of the bolt is serrated to ensure that the eloxal coating is broken up to establish a good electrical contact.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	1.40 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  T-Slot bolts, Stainless Steel

  GANTER

  Stainless Steel-T-Slot bolts GN 505.5 can be inserted vertically into the slot. During tightening, the bolt is forced into the crosswise position and thus anchored in the slot. Conversely, the bolt is turned back during loosening and can then be removed.
  The clamping face of the bolt is serrated to ensure that the eloxal coating is broken up to establish a good electrical contact.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	5.80 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  Rhombus T-Nuts

  GANTER

  Rhombus T-Nuts GN 508.1 can be inserted vertically into the T-Slot.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	4.20 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  Swing bolts, Stainless Steel

  GANTER

  Precision type Stainless Steel-Swing bolts DIN 444 are mainly used for jigs and fixtures.
  Threads and thread lengths not listed in the above table are available on request.

  • Volume Discount

  Starting from∗ ：	8.74 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  T-Nuts / GN 506.2 / M4, M5, M6, M8

  GANTER

  T-Nuts GN 506.2 can be turned into position, i.e. they can be inserted at any point along the slot.
  The spring washer prevents the nut from inadvertently being displaced inside the slot, which is particularly advantageous if the profile rail is arranged vertically. The outstanding feature of this design is that different slot heights can be bridged.
  As an example, T-Nuts GN 506.2 can be used to fit hinges to commercially available extrusion rails.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	1.28 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  T-Nuts / Stainless Steel / GN 506.1 / M4, M5, M6, M8

  GANTER

  T-Nuts GN 506.1 can be turned into position, i.e. they can be inserted at any point along the slot.
  The spring loaded ball will prevent an unwanted movement of the nut in the slot which can easily occur on a bed with the T-slots in a vertical position.
  As an example Nuts GN 506.1 can be used to fit hinges to commercially available extrusion rails.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	5.54 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  Swing bolts, Steel

  GANTER

  Precision type swing bolts DIN 444 are mainly used for jigs and fixtures.
  For stocking purposes cylinder head shoulder bolts GN 732 can be used for the sizes M 6, M 8, M 10 and M 12.

  • Volume Discount

  Starting from∗ ：	6.22 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  Swing nuts, Steel

  GANTER

  In combination with grub screws (i.e. DIN 913 or DIN 6379) swing nuts GN 444.2 can be used together as swing bolts in varying lengths.
  In addition, used with a cap screw DIN 912, a swivelling clamping screw can be produced.
  Dimensions d2 ,d3 and s are identical to DIN 444.
  For stocking purposes cylinder head shoulder bolts GN 732 can be used for the sizes M8, M10 and M12.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	10.40 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  T-Nuts with guide step

  GANTER

  T-Nuts GN 506 can be turned into position, i.e. they can be inserted at any point along the slot.
  The guide step positions the nut parallel and centered in relation to the slot, a configuration which eases the sliding movement and prevents the assembly from twisting during tightening.
  The spring element (ball / pressure spring) prevents the nut from accidentally sliding inside the slot, which is particularly advantageous when the profile rail is mounted perpendicularly.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	0.78 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  T-Nuts with slip proof

  GANTER

  T-nuts GN 508.2 are dimensionally identical to DIN 508.
  They are, however, fitted on the side with a spring loaded ball. This will prevent an unwanted movement of the nut, especially in a vertically mounted T-slot bed.
  

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	3.60 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• • Promotional pricing ends 30/11/2024

  

  T-Nuts without guide step

  GANTER

  T-Nuts GN 506.1 can be turned into position, i.e. they can be inserted at any point along the slot.
  The spring loaded ball will prevent an unwanted movement of the nut in the slot which can easily occur on a bed with the T-slots in a vertical position.
  As an example Nuts GN 506.1 can be used to fit hinges to commercially available extrusion rails.
  

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	1.00 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  T-Nuts, without thread, Stainless Steel

  GANTER

  Stainless Steel-T-Nuts DIN 508 untapped are also available. When ordering the latter the thread size is omitted in part number.

  • Volume Discount

  Starting from∗ ：	6.78 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  T-Nuts, without thread, Steel

  GANTER

  Beyond the scope of the official standard sheet DIN 508, there is also a choice of additional sizes a = 16, 20 and 24.
  T-Nuts DIN 508 untapped with the tensile strength class 8 (blank) are also available. When ordering the latter the thread size is omitted in part number.

  • Volume Discount

  Starting from∗ ：	1.18 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

Loading...