- inCAD Library Home
- > No.000066 Incline measurement fixture
No.000066 Incline measurement fixture
11
11
2 axes of inclination angles can be setup for workpiece verification.
Related Category
Tall Nuts
| Product name | Tall Nuts |
|---|---|
| Part number | NT6 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Economical alternative for a knob
Available sizes
■Tall Nuts
| Material | Surface Treatment | Hardness |
|---|---|---|
| EN 1.1191 Equiv. | Trivalent Bright Chromate Plating | 25 - 30HRC |
| EN 1.4301 Equiv. | - | - |
■Sizes and Dimensions
| Screw Dia. (Coarse) | Height (mm) |
|---|---|
| M6 | 9 |
| M8 | 12 |
| M10 | 15 |
| M12 | 18 |
| M16 | 24 |
| M20 | 30 |
| M24 | 36 |
Clamping Bolts
| Product name | Clamping Screws/Non-Reverse/Serrated Type |
|---|---|
| Part number | HFMG6-25 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
For secure clamping with the tip following the work surface
Available sizes
■Clamping Bolts (Non-reverse, Serrated Type)
| Main body | Ball | ||
|---|---|---|---|
| Material | Surface treatment | Material | Hardness |
| EN 1.7220 Equiv. | Black Oxide | EN 1.3505 Equiv. | 55 - 60HRC |
■Sizes and Dimensions
| Screw Dia. M (Coarse) | Length Selection (mm) | Tip Dia. (mm) |
|---|---|---|
| M6 | 16, 20 - 30 (Increments of 5), 40 | 3.2 |
| M8 | 20 - 50 (Increments of 10), 35 | 4.5 |
| M10 | 25, 30 - 60 (Increments of 10) | 6 |
| M12 | 30, 50, 80 | 7.2 |
| M16 | 40 - 80 (Increments of 20) | 10.7 |
Performance info.
■Speeds / Loads (Load Info.) of Clamping Bolts
| Screw Dia. M (Coarse) | Withstand Load (kN) |
|---|---|
| M6 | 3.3 |
| M8 | 3.9 |
| M10 | 3.4 |
| M12 | 4.8 |
| M16 | 9.6 |
Angle Scales
| Product name | Angle Scale/180Deg. |
|---|---|
| Part number | MEABL50-25-3 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
The tilt can be easily measured visually
Risk info.
Not suitable for high-precision angle measurements
Available sizes
■Angle Scales (90-degree Type)
| Graduation Direction | O.D. (mm) | I.D. (mm) | Installation Hole Dia. (mm) | Material |
|---|---|---|---|---|
| L (Zero at Left) R (Zero at Right) C (Zero at Center) | 20 | 10 | 3 | EN 1.4301 Equiv. |
| 30 | 15 | |||
| 50 | 25 | |||
| 70 | 40 |
-
TERMS AND CONDITIONS FOR USE OF CAD DATA-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
- 1. CAD Data
- The Data is prepared for assisting the Company's users in the CAD design process by providing dimensions and other Product information. In order to provide the best speed and stability working within this site, the Product drawings were simplified to reduce the size of the Data. For instance, some of the Products are shown without the oil groove shape, screws or spring shape. Also, please be aware that the tolerance, surface roughness and/or chamfer of the Data may vary from the actual Products.
- 2. Disclaimer on Data
- While the Company has carefully prepared the Data, accuracy of the Data is not guaranteed and is subject to the variances as described above. The Company may also modify, add or delete the Data at any time without prior notice. The Company assumes no liability for any direct, indirect, consequential or special damages that you may claim resulted from your use of the Data or any changes to or deletions of the Data regardless of the reason. The Company provides no warranty as to the quality, accuracy, functionality, safety or reliability of the combination of Products and parts. Example applications and combinations of the Products are provided for illustrative purposes only.
- 3. Copyright
-
Copyrights to the content and the Data belong to the Company or the manufacturers of the Products. The said copyright is protected by the Copyright Act and international treaties. The use (including duplication, modification, uploading, posting, transmission, distribution, licensing, sales and publishing) of the Data except for the purpose to use the Data described above without prior approval of the Company is not allowed. The Data cannot be used for any purposes (including sales promotion) except for designing your machine. If you violate this provision or the laws or regulations, the Company may prohibit you from the use of the Data, the Company’s site and/or take legal action. So long as you comply with these terms and conditions, the Company grants to you a non-exclusive, non-transferable, revocable license to access and use the Data for the sole purpose of assisting you in designing machines that incorporate products.
- 4. Disclaimer of Warranty
- ANY AND ALL CONTENT APPEARING ON THIS WEB SITE IS PROVIDED FOR INFORMATIONAL PURPOSES ONLY. THIS WEB SITE, ITS CONTENT AND ITS LINKS ARE PROVIDED ON AN "AS IS" AND "AS AVAILABLE" BASIS AND ARE USED ONLY AT YOUR SOLE RISK, TO THE FULLEST EXTENT PERMISSIBLE BY LAW. THE COMPANY DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, OF ANY KIND, REGARDING THIS WEB SITE (INCLUDING ITS CONTENT, HARDWARE, SOFTWARE AND LINKS), INCLUDING AS TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, TITLE, NON INFRINGEMENT, RESULTS, ACCURACY, COMPLETENESS, ACCESSIBILITY, COMPATIBILITY, SECURITY AND FREEDOM FROM COMPUTER VIRUS. THE COMPANY WILL NOT BE LIABLE FOR ANY DAMAGES OR LOSSES, INCLUDING DIRECT, INDIRECT, CONSEQUENTIAL, SPECIAL, INCIDENTAL OR PUNITIVE DAMAGES AND/OR LOST PROFITS, IN CONNECTION WITH USE OF THE INTERNET, THIS WEB SITE, ITS CONTENT OR ITS LINKS
Further, the Company will not be liable to you for any failure or delay by the Company to provide access to the Data or any of its obligations under these terms and conditions where such failure or delay is the direct or indirect result of any circumstances beyond the Company's reasonable control (and the Company's obligations will be suspended for the duration of such circumstances). - 5. Policy of Third Parties
- You may be required to separately agree to third party's policies if you use third party software to create or browse the Data or use a third party’s CAD data. In this case, the Company does not assume any responsibility for defects of such CAD data or the software of the third party or violation of their rights. Understand them before use.
CAD Data Download (Unit Assembly)
CAD Data Download: File Format
Cautions on the CAD data
-
Assembly data shows the assembly drawings in the concept design phase. The sole purpose of the data is to explain the structure and functionality of the assembly and is not considered nor to be used as a final design.
You will need to edit the Data so that it meets your specific design conditions. -
The CAD data unit assembly consists of sub-assemblies.
Each sub-assembly unit can be used as it is or can be edited. - The Data for fabricated parts is based on easy-to-edit dimensions and shapes in sketches and histories.
- The Data including the third-part components are made by the Company.
* The part in the frame is a sub-assembly unit.
-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
-
- * Unit assembly CAD data consists of some sub-assemblies.
Each sub-assembly unit can be used as it is or can be edited.
Application Overview
Purpose
- Effects of inclination on workpieces (motion property, etc.) can be verified by the individual axis in ±45° range.
Points for use
- Clamping bolts are used to accommodate various sizes and shapes of workpieces.
- Angle of the bottom section of fixture can be adjusted by the hand holding the main body, but angle of the fixture top section can be adjusted using screw and nut knob.
- Measurable angle each: +45°~ -45°, R/L symmetrical
Target workpiece
- Inclination sensor products
Dims.: W500 x D50 x H30mm
Weight up to 1kg
Design Specifications
Operating Conditions or Design Requirements
- Each adjustable angle: ±45°
- External dims.: W154 x D100 x H265mm
Required Performance
- Measurement accuracy: 1° Increment
Selection Criteria for Main Components
- Angular scale
- 1° graduation scale is selected for a simplified measurement.
- Clamping bolts
- Long threaded and swinging head type are selected to support various workpieces.
Design Evaluation
Other Design Consideration
- Low-cost, simplified model-oriented design.
- A bubble level needs to be mounted for level indication.measurement.
- Since it is difficult to absorb the mounting errors of the angular scale on both sides, the angle scales are mounted in dependence to the marking line.
Explore Similar Application Examples
Page
-
/
-
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.